True-rms Utility Multimeter designed for basic electrical tests
The Fluke 113 Utility Multimeter gives utility users the means to quickly and easily do basic meter set and reconnect testing. This meter is simple-to-use and has the features needed to repair most electrical problems. The Fluke 113 has significant improvements over Fluke’s original 7-600, and other utility multimeters. Using the Fluke VCHEK™ LoZ low impedance measurement function, users can simultaneously test for voltage or continuity. The Fluke 113 can perform diode tests, and also provides both auto and manual ranging capabilities. With features such as conformance to the latest safety standards, backlight, and a much larger display that’s easier to view, this new meter is a must have for the utility users toolbox.
Features
Features and benefits of the Fluke 113
VCHEK™ LoZ low impedance measurement function to simultaneously test for voltage or continuity
True-rms for accurate ac measurements on non-linear loads
A large backlit display allows for easy visibility in low-lit areas
Record signal fluctuations using the Min/Max function
Diode test for testing general-purpose germanium, silicon, and power diodes
Integral holster with probe holders for easy storage
Auto and Manual ranging for added user functionality
Meets Measurement Category CAT III 600 V and Category IV 300 V standards for a higher level of safety
The optional TPAK magnetic hanger allows the user hands-free flexibility
Specifications
Specifications
VCHECK 1,2
Range
6.000 V
60.00 V
600.0 V
Resolution
0.001 V
0.01 V
0.1 V
Accuracy
DC, 45 to 500 Hz:2.0 % + 3
500 Hz to 1 kHz: 4.0 % + 3
Diode test 3
Range
2.000 V
Resolution
0.001 V
Accuracy
2.0 % + 3
Continuity3
Range
Resolution
Accuracy
Beeper on < 20 Ω, off > 250 Ω; detects
opens or shorts of 500 μs or longer
Ω3
Range
600.0 Ω
6.000 kΩ
60.00 kΩ
Resolution
0.1 Ω
0.001 kΩ
0.01 kΩ
Accuracy
0.9 % + 2
0.9 % + 1
0.9 % + 1
Capacitance3
Range
1000 nF
10.00 μF
100.0 μF
9999 μF
Resolution
1 nF
0.01 μF
0.1 μF
1 μF
Accuracy
1.9 % + 2
1.9 % + 2
1.9 % + 2
100 μF - 1000 μF: 1.9 % + 2
> 1000 μF: 5 % + 20
Notes: 1 All VChek voltage ranges are specified from 60 counts to 100 % of range. Because inputs below 60 counts are not specified, it is possible and normal for this and other true-rms meters to display non-zero readings when the test leads are disconnected from a circuit or are shorted together. 2 Crest factor of ≤ 3 at 4000 counts, decreasing linearly to 1.5 at full scale. 3 After measuring voltage, a wait time of 1 minute is required to maintain accuracy of ohms, capacitance, diode test, and continuity.
Specifications
Maximum voltage between any terminal and earth ground
600 V
Display
3 3/4-digits, 6000 counts, updates 4/sec
Operating temperature
-10 °C to 50 °C (14 °F to 122 °F)
Storage temperature
-40 °C to 60 °C (-22 °F to 140 °F)
Temperature coefficient
0.1 x (specified accuracy)/°C (< 18 °C or > 28 °C)
Operating altitude
2,000 m
Storage altitude
10,000 m
Relative humidity
95 % to 30 °C
75 % to 40 °C
45 % to 50 °C
Battery type
9 Volt Alkaline, ANSI 1604A / IEC 6F22
Battery life
Alkaline: 300 hours typical, without backlight
Shock
1 Meter drop per IEC 61010-1-2001
Vibration
Per MIL-PRF-28800 for Class 2 instrument
Size (HxWxL)
167.1 mm X 85.1 mm X 46.0 mm (6.58 in X 3.35 in X 1.81 in)
Weight
13.0 oz (404 g)
Safety
Complies with ANSI/ISA 82.02.01 (61010-1) 2004, CAN/CSA-C22.2 No
61010-1-04, UL 61010-1 (2004) and IEC/EN 61010-1 2nd Edition for
measurement Category III, 600 V, Pollution Degree 2, EMC EN61326-1
