Take along the new Fluke 725 Multifunction Process Calibrator, and you're equipped to test and calibrate almost any process parameter. Measure and source mA, volts, temperature (RTDs and thermocouples), frequency, ohms, and pressure, using optional pressure modules.
Do you need to calibrate transmitters? The 725's split display lets you view input and output values simultaneously. For valve and I/P tests, you can source mA while measuring pressure. The 725 has auto-stepping and auto-ramping for remote testing, plus 25% stepping for fast linearity tests.
From the moment you pick it up, the Fluke 725 is ready to perform. Its simple controls, without menus, make operation easy. Its memory functions make set up fast. And its rugged design lets it work as hard as you do.

Source Accuracy
Voltage DC	100.00 mV  0.02%+2 counts 10.000 V  0.02%+2 counts -10.00 mV to 75.00 mV  0.025 % + 1 count (via TC connector)
Current DC	24.000 mA (Source)  0.02%+ 2 counts 24.000 mA (Simulate)  0.02%+ 2 counts
Resistance	15.0 to 400.0 Ω  0.15 Ω (exc. current 0.15 to 0.5 mA), 0.1 Ω (exc. current 0.5 to 2 mA) 401 to 1500 Ω  0.5 Ω(excitation current 0.05 to 0.8 mA) 1500 to 3200 Ω  1 Ω(excitation current 0.05 to 0.4 mA)
Frequency	2.0 to 1000.0 CPM  0.05% 1.0 to 1100.0 Hz  0.05% 1.00 to 10.00 kHz  0.25% Waveform:  5 V p-p squarewave, -0.1 V offset

RTDs and Thermocouples
Measure Accuracy:	NI-120  0.2 °C PT-100 (385)  0.33 °C PT-100 (393)  0.3 °C PT-100 (JIS)  0.3 °C PT-200 (385)  0.2 °C PT-500 (385)  0.3 °C PT-1000 (385)  0.2 °C Resolution:  0.1 °C J:  0.7 °C K:  0.8 °C T:  0.8 °C E:  0.7 °C R:  1.8 °C S:  1.5 °C B:  1.4 °C L:  0.7 °C U:  0.75 °C N:  0.9 °C Resolution  J, K, T, E, L, N, U: 0.1 °C, 0.1 °F B, R, S: 1 °C, 1 °F XK  0.6°C BP  1.2°C
Source Accuracy:	NI-120  0.2 °C PT-100 (385)  0.33 °C PT-100 (393)  0.3 °C PT-100 (JIS)  0.3 °C PT-200 (385)  0.2 °C PT-500 (385)  0.3 °C PT-1000 (385)  0.2 °C Resolution:  0.1 °C Note:  Accuracy stated for 4-wire measurement. J:  0.7 °C K:  0.8 °C T:  0.8 °C E:  0.7 °C R:  1.4 °C S:  1.5 °C B:  1.4 °C L:  0.7 °C U:  0.75 °C N:  0.9 °C Resolution  J, K, T, E, L, N, U: 0.1 °C, B, R, S: 1 °C XK  0.6°C BP  1.2°C

Specifications
Ramp Functions	Source functions:  Voltage, current, resistance, frequency, temperature Ramps  Slow ramp, Fast ramp, 25% step-ramp
Loop Power Function	Voltage:  24 V Accuracy:  10% Maximum current:  22 mA, short circuit protected
Step Functions	Source functions:  Voltage, current, resistance, frequency, temperature Steps  25% of range, 100% of range

Environmental Specifications
Operating Temperature	-10 °C to +55 °C
Storage Temperature	-20 °C to 71 °C
Operating Altitude	3000 m

Safety Specifications
Agency Approvals	EN 61010-1:1993, ANSI/ISA S82.01-1994; CAN/CSA C22.2 No 1010.1:1992

Mechanical & General Specifications
Size	130 x 236 x 61 mm
Weight	0.65 kg
Batteries	4 AA alkaline batteries
Battery Replacement	Separate battery compartment, accessable without breaking calibration seal
Side port connections	Pressure module connector, also used for remote real-time programming