The 743B does the work of several tools – sourcing, simulating and measuring pressure, temperature, and electrical signals in one rugged, hand-held device.
For documentation, the 743B automates calibration procedures and captures your data.
And, of course, it helps you meet rigorous standards like ISO 9000, FDA, EPA and OSHA regulations.
The 743B has a PC interface that lets you download procedures, lists, and instructions created with software-or upload data for printing, archiving, and analysis. With its expanded memory, the 743B can hold a full week of calibrations and procedures.

Source Accuracy
Voltage DC	110.000 mV  0.01%+0.005% * 1.10000 V  0.01%+0.005% * 15.0000 V  0.01%+0.005% *
Current DC	22.000 mA (Source)  0.01%+ 0.015% * 22.000 mA (Simulate)  0.02% + 0.03% *
Resistance	11.000 Ω  0.01% + 20 mΩ 110.00 Ω  0.01% + 40 mΩ 1.1000 kΩ  0.02% + 500 mΩ 11.000 kΩ  0.03% + 5Ω
Frequency	0.00 to 10.99 Hz  0.01 Hz 11.00 to 109.99 Hz  0.1 Hz 110.0 to 1099.9 Hz  0.1 Hz 1100 to 21999 Hz  2 Hz 22.000 to 50.000 kHz  5 Hz
Note	*  (% of reading + % of full scale)

RTDs and Thermocouples
Measure Accuracy:	10 Ω Cu (427):  2 °C 100 Ω Pt (3916):  0.3 °C 100 Ω Pt (3926):  0.3 °C 100 Ω Pt (385):  0.3 °C 200 Ω Pt (385):  0.3 °C 500 Ω Pt (385):  0.3 °C 1000 Ω Pt (385):  0.3 °C 120 Ω Ni (672):  0.3 °C note:  For 2-and 3-wire measurement, add 0.4 °C E:  0.3 °C N:  0.5 °C J:  0.3 °C L:  0.3 °C K:  0.3 °C T:  0.3 °C U:  0.3 °C B:  0.9 °C R:  1.0 °C S:  0.9 °C C:  0.6 °C note:  Accuracy with external cold junction, for internal junction add 0.2 °C
Source Accuracy:	10 Ω Cu (427):  1 °C 100 Ω Pt (3916):  0.1°C 100 Ω Pt (3926):  0.1°C 100 Ω Pt (385):  0.1°C 200 Ω Pt (385):  0.1°C 500 Ω Pt (385):  0.1°C 1000 Ω Pt (385):  0.1°C 120 Ω Ni (672):  0.1°C note:  For 2-and 3-wire simulation, add 0.4 °C E:  0.2 °C N:  0.3 °C J:  0.2 °C L:  0.2 °C K:  0.3 °C T:  0.3 °C U:  0.3 °C B:  0.8 °C R:  0.9 °C S:  0.9 °C C:  0.6 °C note:  Accuracy with external cold junction, for internal junction add 0.2 °C

Specifications
Data Log Functions	Measure functions:  Voltage, current, resistance, frequency, temperature, pressure Reading rate:  1, 2, 5, 10, 20, 30, or 60 readings/minute Maximum record length:  8000 readings (7980 for 30 or 60 readings/minute)
Ramp Functions	Source functions:  Voltage, current, resistance, frequency, temperature Rate:  4 steps/second Trip detect:  Continuity or voltage (continuity detection not available when sourcing current)
Loop Power Function	Voltage:  Selectable, 24 V or 28 V Accuracy:  5% Maximum current:  22 mA, short circuit protected Maximum input voltage:  30 V DC
Step Functions	Source Functions  Voltage, current, resistance, frequency, temperature Manual Step  Selectable step, change with arrow buttons Autostep  Fully programmable for function, start delay, stepvalue, time per step, repeat

Environmental Specifications
Operating Temperature	-10°C to +50°C  -20°C to +50°C *
Storage Temperature	-20°C to +60°C
Dust/water resistance	Meets IP52, IEC 529
Operating Altitude	2800 m
Note	*  Except frequency and AC

Safety Specifications
Agency Approvals	CAN/CSA C22.2 No 1010.1-92, ASNI/ISA S82.01-1994, UL3111, and EN610-1:1993

Mechanical & General Specifications
Size	130 x 236 x 61 mm
Weight	1.4 kg
Batteries	NiCd:  7.2V, 1.7 Ah
Battery Life	~8 hours typical
Battery Replacement	Via snap-shut door without opening calibrator; no tools required
Side port connections	Pressure module connector  RS-232 connector for PC interface cable  Connection for optional battery eliminator
Data storage capacity	1 week of calibration results
90 day specifications	The standard specification intervals for the 743B is 1 and 2 years.  Typical 90 day measurement and source accuracy can be estimated by   dividing the one year "% of reading" or "%of output" specifications by 2.  Floor specifications, expressed as "% of full scale" or   "counts" or "ohms" remain constant.